? semiconductor components industries, llc, 2006 march, 2006 ? rev. 1 1 publication order number: ne5532/d ne5532, sa5532, se5532, ne5532a, se5532a internally compensated dual low noise operational amplifier the 5532 is a dual high-performance low noise operational amplifier. compared to most of the standard operational amplifiers, such as the 1458, it shows better noise performance, improved output drive capability and considerably higher small-signal and power bandwidths. this makes the device especially suitable for application in high-quality and professional audio equipment, instrumentation and control circuits, and telephone channel amplifiers. the op amp is internally compensated for gains equal to one. if very low noise is of prime importance, it is recommended that the 5532a version be used because it has guaranteed noise voltage specifications. features ? small-signal bandwidth: 10 mhz ? output drive capability: 600 , 10 v rms ? input noise voltage: 5.0 nv hz (typical) ? dc voltage gain: 50000 ? ac voltage gain: 2200 at 10 khz ? power bandwidth: 140 khz ? slew rate: 9.0 v/ s ? large supply voltage range: 3.0 to 20 v ? compensated for unity gain ? pb ? free packages are available http://onsemi.com see detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. ordering information pin connections soic ? 8 d suffix case 751 pdip ? 8 n suffix case 626 1 8 1 8 16 1 soic ? 16 wb d suffix case 751g n, d8 packages d package* *sol and non-standard pinout. 7 6 5 4 3 2 1 b a v+ out b ? in b +in b out a ? in a +in a v- top view ? in a +in a nc v ? nc nc +in b ? in b nc nc nc out a 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 15 v+ out b nc nc top view 8 see general marking information in the device marking section on page 6 of this data sheet. device marking information
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 2 figure 1. equivalent schematic (each amplifier) + _ maximum ratings rating symbol value unit supply voltage v s 22 v input v oltage v in v supply v differential input voltage (note 1) v diff 0.5 v operating temperature range ne5532/a sa5532 se5532/a t amb 0 to 70 ? 40 to +85 ? 55 to +125 c storage t emperature t stg ? 65 to +150 c junction t emperature t j 150 c maximum power dissipation, t amb = 25 c (still-air) 8 d8 package 8 n package 16 d packagee p d 780 1200 1200 mw thermal resistance, junction ? to ? ambient 8 d8 package 8 n package 16 d packagee r ja 182 130 140 c/w lead soldering temperature (10 sec max) t sld 230 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. diodes protect the inputs against overvoltage. therefore, unless current-limiting resistors are used, large currents will flow if the differential input voltage exceeds 0.6 v. maximum current should be limited to 10 ma.
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 3 dc electrical characteristics (t amb = 25 c; v s = 15 v, unless otherwise noted.) (notes 2, 3 and 4) characteristic symbol test conditions se5532/a ne5532/a, sa5532 unit min typ max min typ max offset voltage v os ? ? 0.5 2.0 ? 0.5 4.0 mv ? overtemperature ? ? 3.0 ? ? 5.0 mv v os / t ? ? 5.0 ? ? 5.0 ? v/ c offset current i os ? ? ? 100 ? 10 150 na ? overtemperature ? ? 200 ? ? 200 na i os / t ? ? 200 ? ? 200 ? pa/ c input current i b ? ? 200 400 ? 200 800 na ? overtemperature ? ? 700 ? ? 1000 na i b / t ? ? 5.0 ? ? 5.0 ? na/ c supply current i cc ? ? 8.0 10.5 ? 8.0 16 ma ? overtemperature ? ? 13 ? ? ? common-mode input range v cm ? 12 13 ? 12 13 ? v common-mode rejection ratio cmrr ? 80 100 ? 70 100 ? db power supply rejection ratio psrr ? ? 10 50 ? 10 100 v/v large-signal voltage gain a vol r l 2.0 k ; v o = 10 v 50 100 ? 25 100 ? v/mv overtemperature 25 ? ? 15 ? ? r l 600 ; v o = 10 v 40 50 ? 15 50 ? overtemperature 20 ? ? 10 ? ? output swing v out r l 600 12 13 ? 12 13 ? v overtemperature 10 12 ? 10 12 ? r l 600 ; v s = 18 v 15 16 ? 15 16 ? overtemperature 12 14 ? 12 14 ? r l 2.0 k 13 13.5 ? 13 13.5 ? overtemperature 12 12.5 ? 10 12.5 ? input resistance r in ? 30 300 ? 30 300 ? k output short circuit current i sc ? 10 38 60 10 38 60 ma 2. diodes protect the inputs against overvoltage. therefore, unless current-limiting resistors are used, large currents will flow if the differential input voltage exceeds 0.6 v. maximum current should be limited to 10 ma. 3. for operation at elevated temperature, derate packages based on the package thermal resistance. 4. output may be shorted to ground at v s = 15 v, t amb = 25 c. temperature and/or supply voltages must be limited to ensure dissipation rating is not exceeded.
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 4 ac electrical characteristics ( t amb = 25 c; v s = 15 v, unless otherwise noted.) characteristic symbol test conditions ne/se5532/a, sa5532 unit min typ max output resistance r out a v = 30 db closed-loop f = 10 khz, r l = 600 ? 0.3 ? overshoot ? voltage-follower % v in = 100 mv p-p ? 10 ? c l = 100 pf; r l = 600 gain a v f = 10 khz ? 2.2 ? v/mv gain bandwidth product gbw c l = 100 pf; r l = 600 ? 10 ? mhz slew rate sr ? ? 9.0 ? v/ s power bandwidth ? v out = 10 v ? 140 ? khz v out = 14 v; r l = 600 ? 100 ? v cc = 18 v electrical characteristics ( t amb = 25 c; v s = 15 v, unless otherwise noted.) characteristic symbol test conditions ne/se5532 ne/sa/se5532a unit min typ max min typ max input noise voltage v noise f o = 30 hz ? 8.0 ? ? 8.0 12 nv/ hz f o = 1.0 khz ? 5.0 ? ? 5.0 6.0 input noise current i noise f o = 30 hz ? 2.7 ? ? 2.7 ? pa/ hz f o = 1.0 khz ? 0.7 ? ? 0.7 ? channel separation ? f = 1.0 khz; r s = 5.0 k ? 110 ? ? 110 ? db
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 5 typical performance characteristics gain (db) gain (db) 10 10 2 10 3 10 4 10 5 10 6 10 7 120 80 40 0 -40 f (hz) 80 60 40 20 0 -55 -25 0 25 50 75 100 +125 -55 -25 0 25 50 75 100 +125 1,4 1,2 0,8 0,4 0 30 20 10 0 01020 t amb ( o c) typ i o (ma) i i (ma) v in (v) vp; ? v n (v) figure 2. open-loop frequency response 60 40 20 0 -20 10 3 10 4 10 5 10 6 10 7 10 8 f (hz) rf = 10 k ; re = 100 rf = 9 k ; re = 1 k rf = 1 k ; re = 10 2 10 3 10 4 10 5 10 6 10 7 40 30 20 10 0 f (hz) (v) vo(p-p) (nv hz ) i o = 0 0 10 20 0 2 4 6 10 ? 2 10 1 10 ? 1 10 ? 2 10 10 2 10 3 10 4 f (hz) typ typ i p i n (ma) vp; ? v n (v) t amb ( o c) figure 3. closed-loop frequency response figure 4. large ? signal frequency response figure 5. output short ? circuit current figure 6. input bias current figure 7. input common ? mode voltage range figure 8. supply current figure 9. input noise voltage density typical values typical values v s = 15 v typical values v s = 15 v v s = 15 v typical values
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 6 closed-loop frequency response v oltage-follower + ? 5532 (1/2) 100 pf r s v i r e r f 800 25 + ? 5532 v in v out 100 pf 600 v+ v ? 1 k figure 10. test circuits marking diagrams soic ? 8 d suffix case 751 pdip ? 8 n suffix case 626 a = assembly location wl, l = wafer lot yy, y = year ww, w = work week g or = pb ? free packagee ne5532an awl yywwg ne5532n awl yywwg sa5532n awl yywwg se5532n awl yywwg soic ? 16 wb d suffix case 751g 16 1 ne5532d awlyywwg s5532 alywa 1 8 n5532 alyw 1 8 n5532 alywa 1 8
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 7 ordering information device description temperature range shipping ? ne5532ad8 8 ? pin plastic small outline (so ? 8) packagee 0 to 70 c 98 units / rail ne5532ad8g 8 ? pin plastic small outline (so ? 8) package (pb ? free) 0 to 70 c 98 units / rail ne5532ad8r2 8 ? pin plastic small outline (so ? 8) packagee 0 to 70 c 2500 / tape & reel ne5532ad8r2g 8 ? pin plastic small outline (so ? 8) package (pb ? free) 0 to 70 c 2500 / tape & reel ne5532an 8 ? pin plastic dual in ? line package (pdip ? 8) 0 to 70 c 50 units / rail ne5532ang 8 ? pin plastic dual in ? line package (pdip ? 8) (pb ? free) 0 to 70 c 50 units / rail ne5532d 16 ? pin plastic small outline (so ? 16 wb) package 0 to 70 c 47 units / rail ne5532dg 16 ? pin plastic small outline (so ? 16 wb) package (pb ? free) 0 to 70 c 47 units / rail ne5532dr2 16 ? pin plastic small outline (so ? 16 wb) package 0 to 70 c 1000 tape & reel ne5532dr2g 16 ? pin plastic small outline (so ? 16 wb) package (pb ? free) 0 to 70 c 1000 tape & reel ne5532d8 8 ? pin plastic small outline (so ? 8) packagee 0 to 70 c 98 units / rail ne5532d8g 8 ? pin plastic small outline (so ? 8) package (pb ? free) 0 to 70 c 98 units / rail ne5532d8r2 8 ? pin plastic small outline (so ? 8) packagee 0 to 70 c 2500 / tape & reel ne5532d8r2g 8 ? pin plastic small outline (so ? 8) package (pb ? free) 0 to 70 c 2500 / tape & reel ne5532n 8 ? pin plastic dual in ? line package (pdip ? 8) 0 to 70 c 50 units / rail ne5532ng 8 ? pin plastic dual in ? line package (pdip ? 8) (pb ? free) 0 to 70 c 50 units / rail sa5532n 8 ? pin plastic dual in ? line package (pdip ? 8) ? 40 to +85 c 50 units / rail SA5532NG 8 ? pin plastic dual in ? line package (pdip ? 8) (pb ? free) ? 40 to +85 c 50 units / rail se5532ad8 8 ? pin plastic small outline (so ? 8) packagee ? 55 to +125 c 98 units / rail se5532ad8g 8 ? pin plastic small outline (so ? 8) package (pb ? free) ? 55 to +125 c 98 units / rail se5532ad8r2 8 ? pin plastic small outline (so ? 8) packagee ? 55 to +125 c 2500 / tape & reel se5532ad8r2g 8 ? pin plastic small outline (so ? 8) package (pb ? free) ? 55 to +125 c 2500 / tape & reel se5532n 8 ? pin plastic dual in ? line package (pdip ? 8) ? 55 to +125 c 50 units / rail se5532ng 8 ? pin plastic dual in ? line package (pdip ? 8) (pb ? free) ? 55 to +125 c 50 units / rail ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd801 1/d.
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 8 package dimensions soic ? 8 nb case 751 ? 07 issue ag seating plane 1 4 5 8 n j x 45 k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 6. 751 ? 01 thru 751 ? 06 are obsolete. new standard is 751 ? 07. a b s d h c 0.10 (0.004) dim a min max min max inches 4.80 5.00 0.189 0.197 millimeters b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.053 0.069 d 0.33 0.51 0.013 0.020 g 1.27 bsc 0.050 bsc h 0.10 0.25 0.004 0.010 j 0.19 0.25 0.007 0.010 k 0.40 1.27 0.016 0.050 m 0 8 0 8 n 0.25 0.50 0.010 0.020 s 5.80 6.20 0.228 0.244 ? x ? ? y ? g m y m 0.25 (0.010) ? z ? y m 0.25 (0.010) z s x s m 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 mm inches scale 6:1 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting t echniques reference manual, solderrm/d. soldering footprint*
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 9 package dimensions 8 ? pin plastic dual in ? line package (pdip ? 8) n suffix case 626 ? 05 issue l notes: 1. dimension l to center of lead when formed parallel. 2. package contour optional (round or square corners). 3. dimensioning and tolerancing per ansi y14.5m, 1982. 14 5 8 f note 2 ? a ? ? b ? ? t ? seating plane h j g d k n c l m m a m 0.13 (0.005) b m t dim min max min max inches millimeters a 9.40 10.16 0.370 0.400 b 6.10 6.60 0.240 0.260 c 3.94 4.45 0.155 0.175 d 0.38 0.51 0.015 0.020 f 1.02 1.78 0.040 0.070 g 2.54 bsc 0.100 bsc h 0.76 1.27 0.030 0.050 j 0.20 0.30 0.008 0.012 k 2.92 3.43 0.115 0.135 l 7.62 bsc 0.300 bsc m ??? 10 ??? 10 n 0.76 1.01 0.030 0.040
ne5532, sa5532, se5532, ne5532a, se5532a http://onsemi.com 10 package dimensions soic ? 16 wb d suffix case 751g ? 03 issue c d 14x b 16x seating plane s a m 0.25 b s t 16 9 8 1 h x 45 m b m 0.25 h 8x e b a e t a1 a l c notes: 1. dimensions are in millimeters. 2. interpret dimensions and tolerances per asme y14.5m, 1994. 3. dimensions d and e do not inlcude mold protrusion. 4. maximum mold protrusion 0.15 per side. 5. dimension b does not include dambar protrusion. allowable dambar protrusion shall be 0.13 total in excess of the b dimension at maximum material condition. dim min max millimeters a 2.35 2.65 a1 0.10 0.25 b 0.35 0.49 c 0.23 0.32 d 10.15 10.45 e 7.40 7.60 e 1.27 bsc h 10.05 10.55 h 0.25 0.75 l 0.50 0.90 q 0 7 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scil lc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, in cluding without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different ap plications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical ex perts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc prod uct could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemn ify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney f ees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was neglig ent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada japan : on semiconductor, japan customer focus center 2 ? 9 ? 1 kamimeguro, meguro ? ku, tokyo, japan 153 ? 0051 phone : 81 ? 3 ? 5773 ? 3850 ne5532/d literature fulfillment : literature distribution center for on semiconductor p.o. box 61312, phoenix, arizona 85082 ? 1312 usa phone : 480 ? 829 ? 7710 or 800 ? 344 ? 3860 toll free usa/canada fax : 480 ? 829 ? 7709 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : http://onsemi.com order literature : http://www.onsemi.com/litorder for additional information, please contact your local sales representative.
|
